Norge
Tullfri*
- Deras linjer2 norska linjer
87.08.9410 For the vehicles of heading 87.01
Norska tulldata kontrollerade 13 september 2026.
Kod 8708 94 · Nummer 8708
Officiell tulltext
Rattar, styrkolonner och styrväxlar samt delar till sådana, för traktorer, motorfordon för transport av minst 10 personer inkl. föraren, bilar och andra motorfordon konstruerade huvudsakligen för personbefordran, motorfordon för godsbefordran samt motorfordon för speciella ändamål, andra än sådana som är konstruerade huvudsakligen för person- eller godsbefordran
Välj den beskrivning som passar din vara bäst.
Importtull på koderna nedan: 3.5–4.5%*
4 koder under den här
Prova ett kortare ord, eller sök i hela tulltaxan i stället.
Försäljning till Norge, Storbritannien och USA
Norge, Storbritannien och USA har egna tulltaxelinjer under det 6-siffriga HS-numret. Satserna nedan är det deras tullmyndigheter tar ut på varor som kommer från EU. Stäm av varorna mot varje lands egen ordalydelse innan du förlitar dig på en sats.
Norge
Tullfri*
87.08.9410 For the vehicles of heading 87.01
Norska tulldata kontrollerade 13 september 2026.
Storbritannien
Från 0.0 % till 4.0 %*
8708 94 20 00 For the industrial assembly of: Vehicles of heading|8703; Vehicles of heading|8704|with
Nordirland följer andra regler.
Brittiska tulldata kontrollerade 13 september 2026.
USA
15.0%†
Bedömd utifrån offentliggjorda amerikanska åtgärder
8708.94.10.00 Parts and accessories of the motor vehicles of headings 8701 to 8705, Other parts
Den amerikanska importören lämnar in tulldeklarationen.
Amerikanska tulldata kontrollerade 16 september 2026.
Norge delar upp den 6-siffriga kategorin på sitt eget sätt, så det här är Norges egna rader under den, inte den här EU-koden. Stäm av din vara mot deras ordalydelse; vad norska tullen tar ut visas per rad.
87.08.9410
For the vehicles of heading 87.01
87.08.9490
Other
Innehåller data från norska tullen (data.toll.no), licensierad under CC BY 4.0, anpassad för visning.
Så här mycket tar brittiska tullen ut när varor som dessa anländer till Storbritannien.
8708 94 20 00
For the industrial assembly of: Vehicles of heading|8703; Vehicles of heading|8704|with either a compression-ignition internal combustion piston engine (diesel or semi-diesel) of a cylinder capacity not exceeding 2|500|cm$3|or with a spark-ignition internal combustion piston engine of a cylinder capacity not exceeding 2|800|cm$3; Vehicles of heading|8705
8708 94 35 00
Steering wheels, steering columns and steering boxes
8708 94 91 00
Of closed-die forged steel
8708 94 99 10
Hub gear made of cold rolled carbon steel (per ASTM A1008), molded into the plastic and pressed on pinion, with: -an outer diameter of 81,2 mm or more, but not more than 82,55 mm, -an inner diameter of 25,9 mm or more, but not more than 25,97 mm, -a height of the lower side of inner diameter of 11,63 mm or more, but not more than 12,13 mm, -a height of the upper side of inner diameter of 3,25 mm or more, but not more than 3,5 mm, -an overall height of 11,63 mm or more, but not more than 19,5 mm for use in the manufacture of vehicle's steering system
8708 94 99 20
Intermediate steering shaft forming part of the steering column with: -a torsional rigidity of 25 Nm/degree or more, -a tubular male shaft in welded carbon steel tube (per GB/T 699 grade 20), -a tubular female shaft in welded carbon steel tube (per with GB/T 699 grade 20), -two spiders universal joint made of chromium alloy steel (per GB/T 5216 grade 20CrMnTiH), -a length in nominal telescope position of 396 mm or more but not more than 467 mm, -a coupling interface on both ends with internal toothing, -two cardan joints on both sides, -a telescope shaft function with a range of 74 mm or more but not more than 115 mm, for use in the manufacture of vehicle's steering system
8708 94 99 30
Lower assist shaft as part of the steering column made of carbon steel (per GB/T699 grade 45 or JIS G4051 grade S45C) with: -an ultimate torsional strength load of 325 Nm or more and Johnson Apparent Elastic Limit (J.A.E.L) values of 275 Nm or more, -a length of 66,39 mm or more but not more than 88,64 mm, -an outer diameter of 27,47 mm or more but not more than 28,38 mm, -an inner hole of diameter 6,50 mm or more but not more than 6,58 mm, -an external 26-teeth spline with major diameter 21,18 mm or more but not more than 21,44 mm, -a knurling on a part of outer surface of major diameter 26,0 mm or more but not more than 26,1 mm, -with or without an external 24-tooth spline and with a major diameter 24,75 mm or more but not more than 25 mm, for use in the manufacture of vehicle's steering system
8708 94 99 40
Upper assist shaft as part of the steering column made of carbon steel (per GB/T699 grade 45) with: -an ultimate torsional strength load of 325 Nm or more and Johnson Apparent Elastic Limit (J.A.E.L) values of 275 Nm or more, -a length of 165,3 mm or more but not more than 204,2 mm, -an outer diameter of 22,87 mm or more but not more than 22,92 mm, -an internal hole of diameter 6,50 or more but not more than 6,58 mm, -an external spline, for use in the manufacture of vehicle's steering system
8708 94 99 50
Lower shaft as part of the steering column made of aluminium alloy (per ASTM B221M grade 6105), air quenched and tempered with: -an ultimate torsional strength of 260 Nm or more, -a length of 296,7 mm or more but not more than 297,8 mm, -an external 18-tooth spline on all shaft length with major diameter of 28,7 mm or more but not more than 29 mm, -an 18-tooth internal spline with a minor diameter of 19,7 mm or more but not more than 20 mm, for use in the manufacture of vehicle's steering system
8708 94 99 60
Torsion bar as part of the steering column made of carbon alloy steel (per SAE J1268, grade 5160H of modified chemistry for carbon content of 0,53 or more, but not more than 0,56) with: -a shaft torsional stiffness of 2,5 Nm/degree or more but not more than 2,7 Nm/degree, -a length of 107,75 mm or more but not more than 108,25 mm, -an outer diameter of 6,38 mm or more but not more than 6,42 mm, -two external 18-tooth splines on both shaft ends with a major diameter of 6,70 mm or more but not more than 6,85 mm, as interface to pressing with matting input and output shafts, -entire surface shot peened, for use in the manufacture of vehicle's steering system
8708 94 99 70
Tubular steering shaft as part of the steering column made of carbon steel welded tube (per EN 10305/2, E235 C or GB/T699 grade 20) with: -an ultimate torsional strength of 300 Nm or more and Johnson Apparent Elastic Limit (J.A.E.L) values of 275 Nm or more, -a length of 245,48 mm or more but not more than 287,5 mm, -an outer diameter of 23,95 mm or more but not more than 32,25 mm, -an interface for steering wheel connection either in a form of an external 40-tooth spline with major diameter of 17,1 mm or more but not more than 17,5 mm and an internal thread M12x1,75-6H or in a form of an external hexagon with a short diagonal of 15,05 mm or more but not more than 15,35mm and an internal thread M10x1.5-6H, -an interface either in a form of an internal 10-tooth spline of length of 98.0 mm or more but not more than 160 mm, with minor diameter of 16,1 mm or more but not more than 16,4 mm or in a form of an internal 48-tooth spline of length of 151 mm or more but not more than 160 mm, with minor diameter of 23,2 mm or more but not more than 23,3 mm, for use in the manufacture of vehicle's steering system
8708 94 99 80
Blank assembly worm gear, consisting of a hub of carbon steel (GB/T 699 grade 25 or DIN EN 10277 grade 11SMn30) and a ring of cast polyamide 6/12 with: - an outer diameter of 97,35 mm or more, but not more than 102,65 mm, - an inner diameter of 27,91 mm or more, but not more than 27,93 mm, - a height of the hub of 11,75 mm or more, but not more than 12,00 mm, - an overall height of 16,00 mm or more, but not more than 18,00 mm
8708 94 99 90
Other
Tullsatserna gäller i Storbritannien, alltså England, Skottland och Wales. För varor som förs in i Nordirland kan andra regler gälla.
Innehåller information från offentlig sektor som är licensierad under Open Government Licence v3.0.
Källa: UK Department for Business and Trade (data.api.trade.gov.uk).
Det som amerikansk tull tar ut när varor som dessa anländer från EU. Den amerikanska importören lämnar in tulldeklarationen och betalar tullen.
8708.94.10.00
Parts and accessories of the motor vehicles of headings 8701 to 8705, Other parts and accessories, Steering wheels, steering columns and steering boxes; parts thereof, Steering wheels, steering columns and steering boxes, For tractors suitable for agricultural use
8708.94.50.00
Parts and accessories of the motor vehicles of headings 8701 to 8705, Other parts and accessories, Steering wheels, steering columns and steering boxes; parts thereof, Steering wheels, steering columns and steering boxes, For other vehicles
8708.94.60.00
Parts and accessories of the motor vehicles of headings 8701 to 8705, Other parts and accessories, Steering wheels, steering columns and steering boxes; parts thereof, Parts, For tractors suitable for agricultural use
8708.94.65.00
Parts and accessories of the motor vehicles of headings 8701 to 8705, Other parts and accessories, Steering wheels, steering columns and steering boxes; parts thereof, Parts, For other tractors (except road tractors)
8708.94.70.00
Parts and accessories of the motor vehicles of headings 8701 to 8705, Other parts and accessories, Steering wheels, steering columns and steering boxes; parts thereof, Parts, For other vehicles, Of cast iron
8708.94.75.10
Parts and accessories of the motor vehicles of headings 8701 to 8705, Other parts and accessories, Steering wheels, steering columns and steering boxes; parts thereof, Parts, For other vehicles, Other, Steering shaft assemblies incorporating universal joints
8708.94.75.50
Parts and accessories of the motor vehicles of headings 8701 to 8705, Other parts and accessories, Steering wheels, steering columns and steering boxes; parts thereof, Parts, For other vehicles, Other
Antidumpingtull, utjämningstull, amerikanska importavgifter och tullavgifter räknas inte in.
Beskrivningarna ovan är de amerikanska tarifftexterna, som USA bara publicerar på engelska.
Källa: den amerikanska tulltaxan från US International Trade Commission (hts.usitc.gov), public domain, och de åtgärder som offentliggjorts i Federal Register.
Det här är en planeringsuppskattning utifrån den amerikanska tulltaxan (revisionen är angiven) och de åtgärder som offentliggjorts i Federal Register per det angivna datumet, för en sändning med ursprung i EU. Det är inte en tulldeklaration, juridisk rådgivning eller ett tullombuds bedömning, och tullkoder.se är inte ett amerikanskt auktoriserat tullombud. Den amerikanska importören eller dess tullombud bekräftar klassificeringen, ursprunget, värdet och tullen som ska betalas innan deklarationen lämnas in.
Tullsatserna här är uppskattningar, avlästa ur officiella tulltaxedata från EU, Norge och Storbritannien och bara till orientering. Kontrollera den aktuella satsen hos Tullverket, TARIC, norska tullen eller brittiska Online Trade Tariff innan du deklarerar. Satsen du betalar kan också bero på varans ursprungsland. Det här är grundtullsatser: importmoms, punktskatter, antidumpningstullar samt skydds- och kvotåtgärder ingår inte.
Skapa ett gratiskonto för att samla de tullkoder du behöver på ett ställe och komma tillbaka till dem när du vill.